







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Delta Bathroom Remodeling in Irving: What to Know First
Delta bathroom remodeling in Irving typically runs $9,000 to $28,000, most full baths land in the $12,000 to $18,000 range, and a planned remodel takes two to four weeks from demo to final inspection. We give you a written price before any work starts, so the number you approve on day one is the number on the invoice. This page is for Irving homeowners with Delta fixtures already in the bath – a Delta shower trim, a Delta tub filler, a Delta toilet in the hall bath – who want that hardware handled correctly while the room around it gets rebuilt. Call (844) 320-5939 for a free estimate.
Key Takeaways
- Full Delta bathroom remodels in Irving: $9,000 to $28,000, with a written price before demo.
- Small bathroom remodels: $5,000 to $12,000; walk-in showers: $4,500 to $12,000.
- Delta’s pressure-balance valves are common in Irving homes built from the 1980s through the 2000s – we rebuild or replace them while the wall is open.
- Every job carries our 365-Day Done Right Promise in writing.
- We’re an independent Delta service provider, not affiliated with or authorized by Delta.
How Delta Products Fail – and How We Fix Them

Delta builds reliable hardware, but the DFW climate and Irving’s hard, mineral-heavy water treat it a certain way. Here are the failure modes our technicians actually see, and what we do about each.
- Monitor 13 and 14 series pressure-balance cartridges seize up. These are the most common Delta shower valves in Irving homes from the 1990s onward. Our water leaves scale behind, and the balancing spool inside the cartridge stops shifting, so the shower runs scalding or lukewarm no matter where you turn the handle. We pull the cartridge, flush the valve body, and set a new OEM cartridge while the wall is open.
- Delta MultiChoice rough-in valves get installed with the wrong depth. The universal rough-in is popular with builders, but if the valve sits too deep or too shallow in the stud bay, the trim won’t seal and water works behind the tile. During demo we measure the valve body against the finished wall and correct the depth before new tile goes on.
- Chrome and SpotShield trim corrodes at the base plate. Irving’s humidity swings and daily shower use pit the finish at the escutcheon seam, and the screws corrode first. We inspect the trim seating and replace gaskets and seals, and if the finish is failing we spec a fresh Delta trim kit that fits the existing rough-in.
- Delta toilet fill and flush valves wear out quietly. A running Delta toilet can waste hundreds of gallons a month and stain the bowl with mineral deposits. We replace the fill valve and flapper with OEM parts – aftermarket flappers fit loosely and leak within a year – and check the supply line while the tank is off.
- Tub spouts and hand showers leak at the threads. The diverter spout on older Delta tub fillers loses its seal and drips behind the tub skirt, which rots the substrate out of sight. We open it up, replace the spout and the wet-wall substrate, then reset tile on cement board.
One parts note worth knowing: Delta replacement cartridges are widely copied, and cheap aftermarket versions fit the valve but fail the temperature-balance test. We use OEM Delta cartridges on every rebuild so the valve keeps its rating and the trim warranty isn’t voided by mismatched parts.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Our Delta Bathroom Remodeling Process
- 1
Walkthrough and diagnostics. We look at every Delta fixture in the room, test the shower valve, check the toilet and the supply lines, and note what can be reused versus what’s failing.
- 2
Written price and plan. You get a line-item written price before anything is pulled – demo, plumbing, substrate, tile, fixtures, and the Delta parts we’re keeping or replacing.
- 3
Parts decision. We confirm OEM Delta cartridges and trim, and tell you plainly where a quality aftermarket part is fine and where it isn’t.
- 4
Demo and rough-in. We protect the rest of the house, pull the old surfaces, correct the valve depth and supply lines, and set moisture-resistant cement board as the substrate (the layer behind your tile).
- 5
Tile, trim and test. New tile goes down, Delta trim and fixtures go back on, and we pressure-test the valve and check every connection for leaks before we call the job done.
- 6
Cleanup and the guarantee. We leave the room cleaner than we found it and hand you a written guarantee – the 365-Day Done Right Promise – on the whole job.
See the difference
Before
After
Before
After
Before
AfterWhat Delta Bathroom Remodeling Costs in Irving

Here’s what Delta bathroom work actually costs in Irving, priced as ranges so you can plan. These are real numbers, not ballparks.
| Job | Typical Cost in Irving |
|---|---|
| Full bathroom remodel (with Delta fixtures) | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation | $4,500 – $12,000 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Shower replacement | $3,000 – $8,500 |
| Bathroom vanity installation | $800 – $3,000 |
What moves the number: tile selection, whether the shower valve has to be moved, the condition of the substrate once demo opens the wall, and how many Delta fixtures you keep versus replace. A simpler finish on a small bath can land near the low end; a full gut with a curbless shower and new tile runs toward the top. Call (844) 320-5939 for an exact written price – estimates are free.
Why Irving Homeowners Call Penhallow Remodeling Irving for Delta Work
Most of our Irving customers have already been burned once – a price that grew after demo day, a shower that leaked six weeks later. So we work differently. Every job gets a written price before work starts and a defined arrival window. Our technicians have up to 22 years of experience, they’re background-checked and arrive in uniform, and a live person answers the phone 24/7, not a voicemail maze.
The 365-Day Done Right Promise covers the work in writing: if something fails inside that year, we come back and fix it at no charge, with a free second visit if a repair doesn’t hold. We know Delta hardware well, and we also handle KraftMaid cabinetry, Kohler and Toto fixtures, and Cambria quartz when your project calls for them. The Kingswell Way says it plainly: say the price before the work, show up in the window, leave the place cleaner than we found it.
FAQs

Not if the fixture is installed to Delta’s spec with genuine Delta parts. We reuse your existing Delta rough-in where it’s sound, use OEM cartridges and trim, and keep the install warranty-safe. If a fixture is out of warranty, we’ll tell you and show you the replacement options.
Often yes. If the tile and substrate around the valve are sound, we can service the valve through the trim opening. If the substrate is failing or the valve needs to move, that’s when a fuller remodel makes sense. We’ll show you which one you’re looking at.
Delta cartridges and trim are widely available, so a valve rebuild usually doesn’t stall the job. Special-order finish colors can add lead time, and we tell you up front when that’s the case so the schedule stays honest.
A full bath runs two to four weeks; a tub-to-shower conversion or small bath is often faster. The biggest variable is what demo reveals behind the wall – we plan for it and price it before we start, so there are no surprise change orders.
Repair if the valve body and rough-in are sound and the failure is a cartridge, seal, or trim. Replace if the valve is corroded out or the finish has failed past the point of a trim kit. We’ll give you the honest call and a written price for either path.
Call (844) 320-5939 for a free estimate on your Delta bathroom remodel in Irving.
Written by the team at Penhallow Remodeling Irving, serving Irving and nearby areas.












